reply

Posted

print

favorite this post Audi 90Q20V, Coupe Quattro 20v, B3, B4, AUDI FACTORY TOOLS FOR SALE, hide this posting unhide

 1 2 3 4 5
Available for your consideration, many are NEW, NIB, & NLA!

Engine (7A):
Model: 2079 : Wrench - Multiple Use . Price: $89.16 * . REMOVE AND INSTALL FRONT PULLEY USE WITH 2084 5 CYL. ENGINE.
Model: 2084: Matra ; Price: $104.18. Counter holder for removing the crankshaft pulley center bolt. 5 Cyl Engine. NO LONGER AVAILABLE New !!!
2079+2084: Wrench Set ; 2079 wrench used to remove crankshaft pulley. It 27mm 12 point. 3/4" dr. Overall length is 345mm. A 2084 Counter holder. The 2084 is no longer available from VW!
Model: 2080A : Seal Installer - Crankshaft. Price: $14.45 * INSTALLATION OF FRONT CRANKSHAFT OIL SEAL 5 - CYLINDER ENGINE REPLACES 2080. (PULLEY SIDE).ALSO USED IN REPAIRING 01A TRANSMISSION.
Model: 3266 : Seal Installer - Crankshaft . Price: $13.78 *. USED TO INSTALL CRANKSHAFT OIL SEAL.
Model: 3203 : Puller - Crankshaft Seal . Price: $103.49 . REMOVE CRANKSHAFT SEALS PULLEY SIDE.
Model: 3129: Seal Installer - Valve Stem . Price: $11.88 * . INSTALL VALVE STEM SEALS ON 4 VALVES PER CYLINDER ENGINES.
Model: 3179; Engine (7A), Ignition distributor TDC alignment. Price: $ 21.78. No longer available!
Engine/Transaxle:
Model: 10-201: Counterhold - Flywheel . Price: $22.18 * . Used when removing and installing dual mass flywheel.
Model: 3176: Alignment Tool - Clutch Plate . Price: $16.69 *. USED IN CENTERING OF THE DRIVE PLATE WHEN ASSEMBLING THE CLUTCH. USED FOR PRESSING HOME OF THE NEEDLE BEARING INTO THE CRANKSHAFT.
Driveline:
Model: 3139: Driveshaft Alignment Fixture . Price: $206.30 * . USED TO REMOVE INSTALL AND ADJUST THE PROPELLERSHAFT/ DIFFERENTIAL DRIVE SHAFT.
Model: 3207: Pressure Spindle . Price: $30.24 *. USED TO DISASSEMBLE OUTER JOINTS OF FRONT & REAR DRIVE SHAFTS.
Model: VW522 : CV Joint Press Sleeve . Price: $22.96 * . FOR INSTALLATION OF INNER CV JOINT.
Model : 40-204a: Press Block . Price: $44.35 . USED TO INSTALL THE INNER CV JOINT AND ALSO TO PULL OUT BALL JOINTS.USED ON MULTIPLE PRESSING OPERATIONS.

Suspension & Steering:
Model: VAG1907 : Steering Centering Bolt . Price: $18.26 * . The steering centering bolt V.A.G 1907 is required for checking the central position of the steering box and steering wheel on the front axle of all VW and Audi 4WD vehicles. The bolt is made of plastic to prevent damage to the steering box.
Suspension:
Hazet : 2593-1: Price $24.99. HAZET, Special 7mm hex key with handle, for installing and removing of the front spring struts on VW-Polo, Derby, Jetta, Scirocco, Passat, Audi 80, 100, 200 and Coupe. No Longer Available.
Hazet: 2593-4: Price $40.70. Drive Nut, remove shock absorber on front strut, 15.5mm hole, 5.0mm slot. Front axle Golf II, III, Jetta, Vento, Passat since 1988, Audi 80 since 1987, similar to VW524.

Matra: 3078: Price $ 49.99. Socket 22mm. Used to remove front spring struts. For VW Golf up to model 1988, Jetta up to model 1987, Scirocco, caddy, Passat, Santana, Audi 80, Golf III, and Vento since model 1993, Passat since Model 1988, Corrado, Audi 100 and 200, Audi Coupe, Audi Quattro.
NOTE: 2593-a,2593-4, & 3078 are used as a set.
Model: 40-201b, Matra; Price $ 28.67. Tube Socket 28mm with 1/2" drive, . USED TO REMOVE THREADED CAP ON FRONT STRUT for Shock adsorber cartridge. Audi 80 since '92, Audi 90 since '87 (similar to VW tool 2069). No longer available !
Model: 2069A: Wrench - Strut . Price $65.99. Tube Socket 33mm, USED TO REMOVE THREADED CAP ON REAR STRUT for shock absorber cartridge, Audi V8 up to '94, VW-Polo since '82, Passat since 88, Audi Coupe, 200 since '84, Audi A6. No Longer Available!
Bilstein: MS 08/7; $43.63. USED TO REMOVE THREADED CAP ON STRUT for Shock adsorber cartridge.
Model: VW519: Press Piece - Multiple Use . Price: $38.75 * . 1.MULTIPLE PRESS OPERATIONS.
2.INST.OIL SEAL TRANS CASE&FINAL DR. 3.INST.DIFF BRG.INNER RACE 5SPD 013. 4.PRESS IN FRT. BEARING HUB.
Model: 3118 : Press Piece - Bushing . Price: $33.38 * . PRESS SUPPORT TOOL USED TO REMOVE AND INSTALL BONDED RUBBER BUSHINGS IN THE FINAL DRIVE & FRONT CONTROL ARM.
Model: 3206: Press Piece - Bushing . Price: $13.22. REMOVE RUBBER BUSHING FROM FRONT CONTROL ARM.

Rear differential:
Model: 30-506B : Bearing Installer - Needle Bearing Price: $14.45 * .INSTALLING TOOL FOR PINION NEEDLE BEARING IN GEAR CARRIER HOUSING FOR 4 & 5 SPEED MANUAL 091/1 AND 094 TRANSMISSIONS.
Model: 2062 : Seal Installer - Driveshaft Flange , Price: $11.65 . INSTALLATION OF OIL SEAL FOR DRIVE SHAFT FLANGE 2.INSTALL TRAN.SIDE COVER SEAL. 5 SPD 016 093.
Model: 3066/2 : Seal Installer - Driver Set - Press Piece ,Price: $16.92 * . USED FOR ASSEMBLY SHAFT SEAL FOR LEFT FLANGE SHAFT/REAR FINAL DRIVE. USED ON 5 SPEED MANUAL GEARBOX 01E.

Model: 3028: Retainer - Drive Flange . Price: $54.66 * . LOCKING DRIVE FLANGE - QUATTRO.
Model: VW391 : Puller - Multiple Use . Price: $73.59 * . Pulling in differential complete with freewheel, pulling off drive flange with gearbox in situ. REMOVE AND INSTALL UNIVERSAL DRIVE FLANGE- 5 SPD 020.
Model: 3026 : Seal Installer - Drive Flange . Price: $34.16 . INSTALL DRIVE FLANGE OIL SEAL QUATTRO.
NOTE: 3028,VW391,& 3026 are used as a set.
Model: 3124: Press Piece - Pivot Mount Bushing . Price: $18.04 * . REMOVE AND INSTALL THE RUBBER BUSHING ON THE REAR DIFFERENTIAL PIVOT MOUNT.


AVAILABLE AS A KIT ONLY, WILL NOT SEPERATE!
Snap On tool trades considered(email Snap On-part #'s & pics ).
Asking ; $1238.86. OBO

UPS-shipping, email your zip.

http://audifans.com/afmktplc/index.php?page=item&id=3702

Can be reached at craigs-direct (or see email at Audifans) any questions, and/or your
tele #, & when you are available.
  • do NOT contact me with unsolicited services or offers

post id: 6620149985

posted:

updated:

best of [?]